| #47431 | Also, if I have to create a list of Save… | 6 years ago |
| #47429 | I would like to create two Saved Command… | 6 years ago |
| #46952 | Correction - traccar for arm is 32-bit s… | 6 years ago |
| #46951 | If you arent going to have a lot of use… | 6 years ago |
| #46948 | Slawek - good idea to have him check CPU… | 6 years ago |
| #46946 | Abou, you are running a 32-bit CPU x86 … | 6 years ago |
| #46941 | Yes he does - already discussed top of t… | 6 years ago |
| #46933 | Download installer from link at top of p… | 6 years ago |
| #46931 | Looks like data stream is missing the co… | 6 years ago |
| #46929 | Change double quotes on config.default t… | 6 years ago |
| #46919 | Since a lot of trackers report time as U… | 6 years ago |
| #46917 | Anton, let me know if there is anything … | 6 years ago |
| #46911 | From running ps ax it looks like you hav… | 6 years ago |
| #46910 | Never mind, I see farther down in code y… | 6 years ago |
| #46905 | Was missing comma in .expression.… | 6 years ago |
| #46903 | Any errors running sudo /opt/traccar/jre… | 6 years ago |
| #46899 | I went into WatchProtocolDecoder.java an… | 6 years ago |
| #46896 | That all looks right
run sudo ps ax … | 6 years ago |
| #46895 | Running server with revised protocol fil… | 6 years ago |
| #46894 | I went ahead and followed the Build tra… | 6 years ago |
| #46889 | Please do not double post the same issue… | 6 years ago |
| #46888 | That means the server has not started an… | 6 years ago |
| #46885 | Instead of loading complete source and r… | 6 years ago |
| #46884 | Did you install as root?
Try sudo se… | 6 years ago |
| #46881 | Do you plan to rebuild distro files lin… | 6 years ago |
| #46879 | Thank you. I was going to look at the co… | 6 years ago |
| #46875 | watch procotol v1.7C formatted:
1710… | 6 years ago |
| #46874 | But everything up to and including the 2… | 6 years ago |
| #46872 | I reset database files and started from … | 6 years ago |
| #46871 | I selected America-New York from pulldow… | 6 years ago |
| #46870 | I figured time wasnt an issue.
But w… | 6 years ago |
| #46865 | Tracker is sending out all position repo… | 6 years ago |
| #46864 | Just created a Saved Command SetTimeZone… | 6 years ago |
| #46863 | and here is actual hex input
watch… | 6 years ago |
| #46862 | Never mind, I see the tracker ID is sent… | 6 years ago |
| #46861 | I am receiving correctly formatted watch… | 6 years ago |
| #46860 | I double checked and tracker is sending … | 6 years ago |
| #46858 | Correction to 2 posts above: Command Res… | 6 years ago |
| #46857 | If I do a CR get location every 20 sec … | 6 years ago |
| #46856 | Also, Command Result Notifications now s… | 6 years ago |
| #46851 | When you select Saved Commands top righ… | 6 years ago |
| #46847 | Every 60 seconds upload time set on tra… | 6 years ago |
| #46846 | Tracker sending out data:
3Gxxxxxxxxx… | 6 years ago |
| #46844 | Update: looking at log, tracker is only … | 6 years ago |
| #46843 | Is there a way to set Server output to i… | 6 years ago |
| #46832 | Resolved: I had to use a different Serve… | 6 years ago |
| #46829 | So I disabled my main site and now tracc… | 6 years ago |
| #46827 | Im already running apache2 and my main … | 6 years ago |
| #46814 | You have to use the Protocol that is imb… | 6 years ago |
| #46794 | Im using the Helicopter Icon now but it… | 6 years ago |