Mictrack 4G GPS Tracker MT600 Feedback
Is there any other way besides using a car battery to power the mt600? I thought I could use it for my robot lawn mower but I don't know how to charge it?
Hi,
You can get one 12V AC adapter to connect to the power wire to charge the device.
if still questions pls email us info@mictrack.com
Thanks,
Mictrack
Hi, I have buyed a Mictrack MT-500, the traccar app recognize the equipment fine, but I dont know how send a command to cut off or/and restore the ignition by the app?
Can any helpme?
The protocol is Tlt2h?
We have not use the Traccar App, but our device protocol are same as TLT-2H.
Hi, the issue is how do I configure in traccar the command to to cut off or/and restore the ignition?
Hi Mictrack, but I dont see any info in TLT-2H protocol info about cut on/off oil?
Hi Mictrack
You posted below
"
mictrack 10 months ago
Hi Alex,
the device can save about 300pcs datas when no signal and the new data will cover the old ones.
Power off/reboot will lost the data.
this is the full protocol for your check.
https://www.mictrack.com/downloads/protocols/Mictrack_HSPA&GPRS_Communication_Protocol_V3.2.pdf
Thanks,
Mictrack
"
If there are ACC OFF/ON events and there´s no signal, is it saved and loaded when signal comes back?
I want to use the equipment to count hours on trucks.
yes, the device will save the ACC OFF/ON events, but pls notice it only can save 300pcs datas and the new coming data will cover the old ones.
Hi! I e-mailed you at info@ but you never responded. I have a few questions:
- I was looking on how to use the USB port on the unit to configure and debug.
- Is there a code to allow the unit to roam onto other networks?
- Is there a code to make the unit 4G LTE only?
Thanks!
Hi Adam,
Sorry we will check the emaill later.
- You can download the Config tool from this link:https://drive.google.com/drive/folders/0B32J3VHnO7UOcHRHbm1LU3p2RlE
- For the roam it's base on your SIM Card, if so the device will support tha like the samrt phone;
- if so need modify the firmware to support that, current device is AUTO mode to connect to 4G/3G or 2G.
Thanks,
Mictrack
Mictrack have released a new multifunction 4G GPS Tracker MT600 Plus, it can extend to support:
- Temperature sensor
- Fuel sensor
- Door sensor
- Siren
- Speaker (two way communication)
- Micrphone( Voice monitor)
More detail pls check the catalog: http://www.mictrack.com/downloads/catalog/MT600_Plus_Catalog.pdf
Thanks,
Mictrack
Hi Mictrack,
I bought the new 4G GPS Tracker MT600 Plus, but I have some questions. For example what commands I should use to change the default password via SMS?
Also is there a command which I can use to interrogate the battery level status for the gps tracker internal battery and for the car/motorbike battery?
Can you please post a complete list of SMS commands supported by MT600 Plus?
Thanks,
Sorin (from Nicosia, Cyprus)
Hi Sorin,
You can change the password by this command: 777+new password+old password
Example: 77712340000 (Default password is 0000)The MT600 Plus will auto-detect the backup battery and car's battery voltage and report to server.
You can check it from the protocol:
https://www.mictrack.com/downloads/protocols/Mictrack_Communication_Protocol_For_MT600_Plus_V1.0.pdfThe latest user manual is: https://www.mictrack.com/downloads/user-manual/4g-gps-tracker/MT600_Plus_User_Manual_V1.0.pdf
MT600 Plus support the Ultrasonic Fuel Level sensor:
https://www.mictrack.com/downloads/user-manual/4g-gps-tracker/UFLS-100_User_Manual_V1.0.pdfThe iButton also will support in the next new firmware.
Please let me know if you have other question.
Thanks,
Mictrack
Hi Mictrack,
Thanks a lot for the full support.
Sorin
Hello Mark,
If sms working fine but no data to server, it should be APN issues.
We suggest call your SIM Card provider to get the correct APN and then set it again by 803 command. As i know the AT&T apn is "phone" if so you can send this command to MT600: #803#0000#phone##
if still issues pls contact us for help info@mictrack.com
Thanks,
Mictrack